Skip to main content

Fehler 1364 beim Clonen einer SSD

Beginner
Posts: 3
Comments: 5

Um meinem Destop-PC eine größere SSD zu spendieren, möchte ich das bisherige Laufwerk clonen, bekomme aber immer den Fehler 1364 (0x1007).

Beim Wechsel einer HDD auf SSD vom Notebook klappte es einwandfrei.

Leider kann ich unter diesem Fehler nichts brauchbares finden, vermutlich weil statt der (0x1007) immer nur andere Angaben zu finden sind. Hat jemand eine Idee hierzu?

 

 

Forum Hero
Posts: 35
Comments: 6089
mvp

Top

[quote=Henner55]

Um meinem Destop-PC eine größere SSD zu spendieren, möchte ich das bisherige Laufwerk clonen, bekomme aber immer den Fehler 1364 (0x1007).

Beim Wechsel einer HDD auf SSD vom Notebook klappte es einwandfrei.

Leider kann ich unter diesem Fehler nichts brauchbares finden, vermutlich weil statt der (0x1007) immer nur andere Angaben zu finden sind. Hat jemand eine Idee hierzu?

------------------------

In order to buy my Destop-PC a larger SSD, I would like to clone the previous drive, but always get the error 1364 (0x1007).

When changing an HDD to SSD from the laptop worked flawlessly.

Unfortunately I can find under this error nothing useful, presumably because of the (0x1007) always only other data to be found. 
Does anyone have an idea?

[/quote]

Hello Henner55,

I'm not familiar with that particular error either, but 1364 is in a few other posts.  Most say to use your Rescue media and not to try cloning from Windows.   

https://forum.acronis.com/forum/126248

https://kb.acronis.com/content/58827

If that is not enough, we'll need a little bit more detail on our system and the two hard drives...

0) What version of Acronis are you using (do you have the latest 2017 5554)

1) What is the make / model / size of the existing drive

2) What is the make /model / size of the new drive

3) Aare they both basic disks or are you using any type of RAID, hybrid disk, or hybrid solution that uses a caching SSD and a regular disk for improved performance

4) What is the SATA mode of your bios set to - AHCI, RAID or something else?

5) Are you trying to start the clone from Acronis in Windows or with your rescue media - please use your rescue media!!!

Forum Hero
Posts: 29
Comments: 5600
mvp

Top

The error is that of a Netlogin Service failure being set to Manual or Disabled.  It does indicate that the attempt to clone was done from within the Windows installed application.

We MVP's advise against cloning a Windows System OS disk from within thei installed application.  Please create bootable Recovery Media and run the Clone operation from that media instead.

You are also strongly advised to create a backup of your Windows System disk prior to running the clone even from the bootable media as a fail safe in case something goes wrong during the clone operation.

Beginner
Posts: 3
Comments: 5

Top

Hello Bobbo,

here are the answeres:

 

0) I use Acronis true image 2017 latest update

1) Kingston 256 GB SATA III

2) Imntenso 512 GB SATA III

3) They are both basic disk I am not using any raid

4) The bios set is AHCI

5) I start it from windows but now I will try frome with the rescue media and will give you a feedback what happened

 

Thanks for it

 

Henner

 

Beginner
Posts: 3
Comments: 5

Top

Now I have done it from the rescue media and it run without any problem.

Thank you for the advice.

 

Henner

 

Forum Hero
Posts: 29
Comments: 9684
mvp

Top

Henner, thanks for giving feedback and glad to hear that all has been successful when using the rescue media.

Forum Hero
Posts: 35
Comments: 6089
mvp

Top

Excellent - glad to hear that the rescue media resolved the issue!